PowerG smoke and heat detector 9936
Battery type: Three AAA batteries
To remove the batteries, complete the following steps:
- Remove the detector from its mounting base by twisting it counterclockwise.
- Note the orientation of the batteries then carefully remove batteries by lifting from the “+” end using a flathead screwdriver.
- Wait at least 30 seconds before installing new batteries to ensure a proper power-down sequence.
To insert the new batteries, complete the following steps:
-
Insert the new batteries, making sure the orientation of the batteries is the same as the batteries that you just removed.
Note: If the batteries are not installed properly, the detector will not operate and the batteries may be damaged. - Reinstall the detector on its mounting base by turning it clockwise until the mating marks align.
-
After the power up sequence, the green LED should blink once every 60 seconds to indicate normal operation.
If the detector does not power up, check that the batteries are installed correctly and fully charged.
PowerG door and window vanishing sensor 9303
Battery type: One 3 V lithium CR2450 battery
To remove the battery, complete the following steps:
- Remove the cover
- Wedge a flathead screwdriver under the battery.
- Twist the screwdriver using the base as a lever to remove the battery.
To insert the new battery, complete the following steps:
- Insert the battery at an angle while observing battery orientation.
- Press down on the battery until it fits into place
PowerG door and window aux sensor 9945
Battery type: One 3 V lithium CR-123A
To remove the battery, complete the following steps:
- Insert a flathead screwdriver into the slot and push upward to remove cover.
- Remove the screw and separate the cover from the base.
- Note the orientation of the battery and then remove it.
To insert the new battery, complete the following steps:
- Install the battery making sure its orientation is the same as the one you just removed.
- Replace the cover.
PowerG temperature sensor 9905
Battery type: One 3 V lithium CR-123A
To remove the battery, complete the following steps:
- Insert a flathead screwdriver into the slot and push upward to remove cover.
- Remove the screw and separate the cover from the base.
- Note the orientation of the battery and then remove it.
To insert the new battery, complete the following steps:
- Install the battery making sure its orientation is the same as the one you just removed.
- Replace the cover.
PowerG shock sensor 9935
Battery type: One 3 V lithium CR-123A
To remove the battery, complete the following steps:
- Insert a flathead screwdriver into the slot and push upward to remove cover.
- Remove the screw and separate the cover from the base.
- Note the orientation of the battery and then remove it.
To insert the new battery, complete the following steps:
- Install the battery making sure its orientation is the same as the one you just removed.
- Replace the cover.
PowerG panic button remote 9938
Battery type: One 3 V lithium CR-2032
To remove the battery, complete the following steps:
- Insert a coin into the slot on the bottom of the unit and twist it open.
- Make sure the elastic pad within the cover remains in place. Put it back in place if it falls off.
- Remove the old battery from its holder.
To insert the new battery, complete the following steps:
- Insert a new battery. Ensure that the “+” side of the battery faces up.
- Test the battery by pressing the button on the fob. The LED indicator should light up.
- Replace the cover securely, making sure that it snaps shut.
PowerG panic CO detector 9933
Battery type: One 3 V lithium CR-123A
To remove the battery, complete the following steps:
- Remove the detector from its mounting base by twisting it counterclockwise.
- Note the orientation of the battery and then remove it.
- Wait at least 20 seconds before installing the new battery to ensure a proper power-down sequence.
To insert the new battery, complete the following steps:
- Install a new battery in the battery compartment observing the correct orientation.
Note: If the battery is not installed correctly, the detector will not operate and the battery may be damaged. If the battery is incorrectly inserted, remove it gently with a flathead screwdriver and correctly reinsert.
- Reinstall the detector onto the mounting bracket by turning it clockwise.
- After the power-up sequence, the green LED blinks once every 12 seconds to indicate normal operation.
PowerG flood detector 9985
Battery type: One 3 V lithium CR-123A
To remove the battery, complete the following steps:
- Insert a flathead screwdriver into the slot and push upward to remove the cover.
- Remove the screw and separate the cover from the base.
- Note the orientation of the battery and then remove it.
To insert the new battery, complete the following steps:
- Install the battery making sure its orientation is the same as the one you just removed.
- Replace the cover.
PowerG glass break detector 9922
Battery type: One 3 V lithium CR-123A
To remove the battery, complete the following steps:
- Press in the snap (located on bottom of the unit) and separate the cover from the base.
- Note the orientation of the battery and then remove it.
To insert the new battery, complete the following steps:
- Install the battery into the battery clips its orientation is the same as the one you just removed.
- Replace the cover.
PowerG motion detector 9914
Battery type: One 3 V lithium CR-123A
To remove the battery, complete the following steps:
- Remove screw located at the bottom of the unit.
- Separate the cover from the base.
- Note the orientation of the battery and then remove it.
To insert the new battery, complete the following steps:
- Install new battery making sure its orientation is the same as the one you just removed.
- Replace cover.
- Insert the screw and tighten. Do not use excessive pressure.
PowerG 4-button keyfob 9939
Battery type: One 3 V lithium CR-2032
To remove the battery, complete the following steps:
- Remove the backside screw
- Open the cover using a screwdriver.
- Note the orientation of the battery and then push it out of its holder.
To insert the new battery, complete the following steps:
-
Install new battery making sure its orientation is the same as the one you just removed.
Note: If the batteries are not installed properly, the unit will not operate and the batteries may be damaged.
- Test the unit by momentarily pressing one of the Transmit buttons. The LED should light up.
- Replace the cover and attach with the screw.