Device |
Additional information |
How to replace battery |
Interlogix door/window sensor – TX-E Series |
Visit the manufacturer’s website |
Note: Only properly trained personnel can replace the battery. When the system indicates that the sensor has a low battery, have it replaced immediately. Use the recommended replacement batteries (3 V, 1 300 mAh, lithium).
To replace the battery:
Caution: Improper use of the battery in this device may cause a fire or chemical burns. Do not recharge, disassemble, heat to more than 100 °C (212 °F) or dispose of it in a fire. Use only the recommended batteries. The use of another battery may cause a fire or explosion. |
Interlogix indoor wireless pet immune PIR detector |
Visit the manufacturer’s website |
The detector is powered by one (1) AA lithium battery. When the system indicates that the sensor has a low battery, replace it immediately. Observe the polarity when installing the new battery, otherwise the sensor may be damaged. When looking at the battery compartment, note that the positive battery end on the left side faces down, while the positive battery end on the right faces up. When the battery is replaced, wait at least three (3) minutes before activating the walk test mode.
Caution: Replace only with one new AA lithium battery. Observe proper polarity when installing the new battery. Installing the battery backwards may cause damage to the sensor. Dispose of used batteries according to the instructions of the manufacturer and/or local authorities. |
Interlogix smoke alarm – TX-6010-01-1 |
|
|
Interlogix flood/freeze sensor - TX-E series
|
Visit the manufacturer’s website |
When the battery is low, a signal is sent to the control panel. To replace the battery:
|
Interlogix 4-button chrome keyfob - TX-E Series |
Visit the manufacturer’s website
|
Because keyfobs are non-supervised devices, a low battery signal will only be received by the control panel when the device is within range of the receiver and a button is pressed (if the device is not in use, no low battery signal will be sent until a button is pressed). When the device is carried beyond the range of the receiver and/or is seldom used/tested, the battery could wholly deplete without a warning of the battery condition being sent to the panel. If the LED on the device appears dim or does not turn on when a button is pressed, it is a warning that the battery may be low or depleted and should be replaced.
To ensure proper functionality, test the device weekly and follow these simple steps to replace the battery when necessary:
|
LIMITED WARRANTY – BATTERY FOR BELL FIBRE EQUIPMENT
Limited Warranty. Bell Canada (including Bell Aliant, a division of Bell Canada) (“Bell”) warrants to you as the original purchaser (“Purchaser” or “you”) the battery purchased for the Fibre Equipment (“Original Battery”) for a period of 12 months from the date of purchase of the Original Battery from Bell (“Warranty Period”) when used in the Fibre Equipment (“Warranty”). “Fibre Equipment” means the Home Hub 3000 modem or UPS (uninterruptible power supply), as applicable, provided by Bell in connection with certain of your Bell services. If the Original Battery fails due to a defect during the Warranty Period, Bell will replace the Original Battery with a new or refurbished battery (“Replacement Battery”). Any warranty coverage that remains during the Warranty Period on the Original Battery (when replaced with a Replacement Battery under this Warranty) will apply to the Replacement Battery. No Replacement Battery has any new or separate warranty coverage. Bell reserves the right to limit the number of Replacement Batteries provided to Purchaser during the Warranty Period.
My Battery Isn’t Working. What Should I Do? Ontario and Québec residents please call Bell at 1 866 310 BELL (2355) and residents of the Atlantic provinces please call 1 866 342-7367, so that Bell can confirm that the Original Battery is within the Warranty Period and attempt to diagnose and correct the malfunction over the telephone. Be sure to keep your proof of purchase to establish the date of purchase of the Original Battery; otherwise Bell may have to estimate the date of purchase.
Limited Warranty Exclusions. This Warranty does not cover any Original Battery or Replacement Battery (each, a Battery) that is:
- damaged due to: abuse, neglect, misuse, accident, theft, vandalism, force majeure events (e.g. fire, flooding, infestation, freezing, power-surge), overcharging or alteration; improper or unauthorized repair, maintenance, installation, set-up or storage; or accessories, wiring or cabling;
- merely discharged and can be recharged and returned to service;
- in Fibre Equipment at a location other than a Bell service address or in a modem or device other than the Fibre Equipment; or
- not owned by the Purchaser.
Exclusive Warranty. To the extent permitted by applicable law (which may vary province to province) and except where prohibited for Québec residents, this Warranty is exclusive and is in lieu of all other warranties, representations, guarantees, terms and conditions, express and/or implied, including merchantability and fitness for a particular purpose. In addition to the rights described in this Warranty, Purchaser may also have other legal rights (which may vary province to province).
Limitation of Liability. To the extent permitted by applicable law and except where prohibited for Quebec residents, Bell's total cumulative maximum liability for negligence, breach of contract, tort or any other claims or causes of action, including fundamental breach, in connection with any Battery or this Warranty is limited to payment, upon request, for actual and direct damages up to a maximum amount equal to the purchase price of the Original Battery, and all other damages, including without limitation indirect, special, consequential, incidental, economic, exemplary or punitive damages, are excluded. You may also be subject to other limitations and exclusions of liability, and obligations, as set out in any Bell terms of service that apply to you. These terms survive the expiry of the Warranty.
Severability; Assignment; Effective Date; Agreement. If any provision of this Warranty is unenforceable, all remaining provisions of this Warranty remain in full force and effect. This Warranty is not assignable by Purchaser. Original Warranty applies only to batteries purchased on or after April 23, 2017 until amended or superceded by Bell. You accept the terms of this Warranty on the earlier of the date you receive a copy or use the Original Battery. If you do not agree with the terms of this Warranty, you have 30 days from the date of your original purchase to return the Original Battery to Bell, unused, for a refund.
More Information. For more information, Ontario and Québec residents should visit www.bell.ca/battery or call Bell at 1 866 310 BELL (2355). Atlantic residents please visit www.bellaliant.ca/battery or call 1 866 342 7367.
Recycling instructions
Bell supports provincial battery recycling programs by remitting Environmental Handling Fees for designated products. For more information about the designated battery types and recycling depot locations, please visit the Call2recycle web-site http://www.call2recycle.ca/.
April 23, 2017
Corporate Secretary’s Office of Bell Canada, Bell Satellite TV (Bell ExpressVu), Bell Mobility,
Bell Media and Bell Aliant. 1 carrefour Alexander-Graham-Bell, Building A-7, Verdun, Québec, H3E 3B3
Device |
Additional information |
How to replace battery |
Honeywell smoke detector- 5808W3A |
Visit the manufacturer’s website |
Use only the recommended replacement batteries: two (2) CR2032 lithium batteries (or equivalent).
To insert or replace the batteries:
|
Honeywell wireless smoke/carbon monoxide (CO) detector - 5800COMBO |
Remove the old batteries. Wait ten seconds, then install four new batteries. To avoid a low battery signal, install the four new batteries in less than 15 seconds. The low battery indicator should turn off once you replace the cover. CAUTION: Improper use of the batteries in this device may cause a fire or chemical burns. Do not recharge, disassemble, heat to more than 100 °C (212 °F) or dispose of them in a fire. Use only Panasonic CR123A lithium batteries. The use of other batteries may cause a fire or explosion. Keep batteries out of the reach of children. Dispose of batteries properly. |
Device |
Additional information |
How to replace battery |
Interlogix door/window sensor – TX-E Series |
Visit the manufacturer’s website |
Note: Only properly trained personnel can replace the battery. When the system indicates that the sensor has a low battery, have it replaced immediately. Use the recommended replacement batteries (3 V, 1 300 mAh, lithium).
To replace the battery:
Caution: Improper use of the battery in this device may cause a fire or chemical burns. Do not recharge, disassemble, heat to more than 100 °C (212 °F) or dispose of it in a fire. Use only the recommended batteries. The use of another battery may cause a fire or explosion. |
Interlogix indoor wireless pet immune PIR detector |
Visit the manufacturer’s website |
The detector is powered by one (1) AA lithium battery. When the system indicates that the sensor has a low battery, replace it immediately. Observe the polarity when installing the new battery, otherwise the sensor may be damaged. When looking at the battery compartment, note that the positive battery end on the left side faces down, while the positive battery end on the right faces up. When the battery is replaced, wait at least three (3) minutes before activating the walk test mode.
Caution: Replace only with one new AA lithium battery. Observe proper polarity when installing the new battery. Installing the battery backwards may cause damage to the sensor. Dispose of used batteries according to the instructions of the manufacturer and/or local authorities. |
Interlogix smoke alarm – TX-6010-01-1 |
|
|
Interlogix flood/freeze sensor - TX-E series
|
Visit the manufacturer’s website |
When the battery is low, a signal is sent to the control panel. To replace the battery:
|
Interlogix 4-button chrome keyfob - TX-E Series |
Visit the manufacturer’s website
|
Because keyfobs are non-supervised devices, a low battery signal will only be received by the control panel when the device is within range of the receiver and a button is pressed (if the device is not in use, no low battery signal will be sent until a button is pressed). When the device is carried beyond the range of the receiver and/or is seldom used/tested, the battery could wholly deplete without a warning of the battery condition being sent to the panel. If the LED on the device appears dim or does not turn on when a button is pressed, it is a warning that the battery may be low or depleted and should be replaced.
To ensure proper functionality, test the device weekly and follow these simple steps to replace the battery when necessary:
|
Device |
Additional information |
How to replace battery |
2GIG passive infrared motion detector –-PIR1-345 |
Visit the manufacturer’s website |
Use only the recommended replacement batteries: one (1) CR123A 3 V lithium battery (or equivalent). To insert or replace the battery:
|
2GIG 4-button keyfob remote -KEY2-345 |
Visit the manufacturer’s website
|
Warning: Improper battery installation may cause an explosion. Replace the batteries only with other batteries of the same or equivalent type as recommended by the manufacturer. Keep batteries out of the reach of young children. If a child swallows a battery, consult a doctor as soon as possible. Do not attempt to recharge batteries. Used batteries should be disposed of in accordance with the waste recovery and recycling regulations in your area. |
2GIG panic button remote - PANIC1-345 |
Visit the manufacturer’s website |
Under normal conditions the battery can last up to 2 years. If the battery is low, the trouble notification will be indicated on the control panel’s screen.
Use only the recommended replacement batteries: 1 Panasonic Lithium CR123A battery or its equivalent.
Users need to perform a system test at least once a year.
|
2GIG flood and temperature sensor – FT1-345 |
Visit the manufacturer’s website |
Installing a new battery: NOTE: Do not install battery until panel is in sensor programming mode.
Replacing a battery:
|
Linear tilt sensor –TILT 345 |
N/A |
|
2GIG glass break detector – GB1-345 |
Visit the manufacturer’s website |
|
Image sensor – ADC-IS-220-GC |
Visit the manufacturer’s website |
When a sensor‘s batteries are low, the panel will display a low battery alert for the sensor.
To replace the sensor batteries, slide the front of the sensor up off the sensor-back. (No need to remove or un-mount entire sensor-back and mounting arm.) To maximize battery life, replace the sensor batteries with 2 AA 1.5v Energizer Ultimate Lithium batteries. Dispose of used batteries according to the battery manufacturer instructions and following local regulations. |
2GIG wireless keypad – PAD1-345 |
Visit the manufacturer’s website |
Use only the recommended replacement batteries: 2 Panasonic Lithium CR2032 or their equivalent.
To install or replace the battery:
WARNING: The polarity of the battery must be observed. Improper handling of lithium batteries may result in heat generation, explosion or fire, which may lead to personal injuries. Replace only with the same or equivalent type of battery as recommended by the manufacturer. Batteries must not be recharged, disassembled or disposed of in fire. Disposal of used batteries must be made in accordance with the waste recovery and recycling regulations in your area. Keep away from small children. If batteries are swallowed, promptly see a doctor. |
2GIG doorbell –DBELL1-345 |
Visit the manufacturer’s website |
If a sensor battery is low, a low battery notification will be indicated on the control panel screen. When the 2GIG system indicates that the sensor has a low battery, replace the battery immediately. Use only the recommended replacement batteries: 2 Panasonic Lithium CR2032 or their equivalent.
|
Nortek Z-Wave dimmable LED standard light bulb – GoControl |
Visit the manufacturer’s website |
|
Linear garage door opener– GD00Z-5 |
N/A |
When the system alerts you that the battery is low, replace it with another CR2032 battery.
|
2GIG wireless carbon monoxide alarm - CO3-345 |
View the product manual (PDF 2.78 MB) |
|
2GIG touchscreen -T51 |
Visit the manufacturer’s website | N/A |